loading

Red light solution on the TSC barcode printers! _ printing equipment

by:Xprinter     2020-06-12
Summary of TSC barcode printers in both the print effect and speed are doing well, but there are still a customer because of ignoring the certain steps that there was a problem printing, most problems can be avoided. Users when using the TSC barcode printers for red light, small make up to this situation the cause of the problem to sort out the following

TSC barcode printers in the printing effect and speed are doing well, but there are still a customer because of ignoring the certain steps that there was a problem printing, most problems can be avoided. For users to use on the situation when TSC barcode printers, small make up to the cause of the problem of the situation as follows, hope the broad masses of users can be ruled out for the corresponding fault, little detours!

TSC barcode printers ERR light has been on a red light, may be the following reasons: ( 1) Machine does not have right to paper, please do hold the pause button on the way of test paper.

( 2) Real size of the label paper is not properly set in the software, please make sure the software set in the high label width and spacing and whether you actually use the same size.

( 3) Sensor type has no right to choose, please confirm whether you label paper is spacing, black label, or continuous paper, and then select the corresponding sensor.

common machine troubleshooting methods:

1, error indicator ( A red light) Normally on

check the pressure of any printer to print. ( 243 series: TTP - 244 +,TTP - 243E Pro、TTP- 342 e Pro except)

2, error indicator ( A red light) Scintillation

turn off the machine, is initialized, the sensor calibration. If the paper is normal, can be a hardware failure possibility. If the paper is not normal. Please check whether the material installed normally; Paper and carbon with matches.

3, machine initialization, a sensor calibration method

a) Two fingers hold PAUSE, FEED button at the same time, don't let go, switch on at the same time.

b) Stay three lights flash in turn, only the FEED release button. Stay away paper, can loosen the PAUSE button. 2 - by normal out of paper is out Three label paper.

c) Press the FEED button, normal paper label for height. And stop at the normal tearing position.

note: this method is applicable to the following a few machines: TTP - 244 +,TTP - 243E Pro、TTP- 342 e Pro

4, model initialization, sensor calibration method 2

a) Holding down the FEED button, don't let go, switch on at the same time. Stay green light flashing, let it go. To turn it off.

b) Print labels for the clearance paper: the holding down the FEED button, don't let go, switch on at the same time. To be orange, red light flashing alternately, let it go.

tag printing for black label paper: holding down the FEED button, don't let go, switch on at the same time. Stay green, and orange lights flashing alternately, let it go.

c) Press the FEED button, normal paper label for height. And stop at the normal tearing position.

note: this method is applicable to the following a few machines: TDP - 225年,TDP - 225W、TTP- 225、TTP- 244CE、 TTP- 245C、TTP- 343C、TTP- 247、TTP- 345年,T200一样; T300

the TSC printer one of the most common problem is the print position deviation. Users should be paid attention to in print or print labels in different sizes for the first time, first needed to adjust the label size, or print position deviation will occur. In fact, the label size adjustment is very simple, all types of TSC printer is equipped with automatic adjustment function, users only need to click the paper FEED test button on the panel, the printer will be detected by the size of the label, to ensure that the print position accurately.

another common problem is the label at the bottom of the paper is too thick, make the size of the sensor can't detect the label for the printer. When the above situation, the user should choose a thinner bottom paper label, of course choose imported eli label paper effect is ideal, and can greatly reduce the damage caused by poor quality of label printing.

Custom message
Chat Online 编辑模式下无法使用
Leave Your Message inputting...
Hello, Thank you for contacting us ! We've received your message and will reply you soon. Have a nice day !