Bar code printers, some of the common problems and the solutions to a problem _ printing devices

Core tip 1, the revised labels don't always keep, advice on hold is springing up a dialog box, according to certain software after closed. Cause: the user directly on the label when the revision of manipulation and provoked. The solution: revised according to accurate correction measures to stop the correction or double-click the you want the content of the correction, in the original layout 1, the revised labels don't always keep, advice on hold is springing up a dialog box, according to certain software after closed. Cause: the user directly on the label when the revision of manipulation and provoked. The solution: revised according to accurate correction measures to stop the correction or double-click the you want the content of the correction, in the original layout dialog box on the correction of writing, do not allow direct correction under the label. So much revised return deformity. 2, bar code printer paper deformity, not only go half zhang, to print a red light (after The inflexible) Cause: the printer parameter Settings. The solution: Z4M inflexible, for example. Click on the start menu - & gt; Settings - & gt; Printer - & gt; Choose Z4M - mechanical & gt; Right-click - & gt; Property - & gt; Printing preferences - & gt; documentOption——> DispenseMode―> Choose TearOff with respect to OK. 3, printer when printing all lights shining not inferior to test paper ( The inflexible) Cause: the sensor fault. The solution: cleaning sensor dust or a change in name. 4, small printer in the print label will not reach the designated position, print the content of partial or total up to partial cause: the label is too small, sensors are difficult to sensor to the paper. The solution: high deformity label at least more than 10 more than just good positioning, otherwise will be end of the label offset Settings. When stop tag set, the tag is set to high than real short a 5 mm, and then stop the shift on the basis of detailed situation the tag offset Settings. 5, when printed font clear, bar code not clear cause: bar code content is too much, the density is too small. The solution: the contraction barcode content or increasing the density. For 200 dpi and 300 dpi inflexible, bar code density anomaly in more than 7 mils to scaling factor to 2 or more than 2, print out the barcode is clear. 6, printed labels, there are always some words to print out cause: the print head is dirty, the layout is wrong. The solution: cleaning the print head; Other can see in the layout of the time to print the word stacked together, the new layout. 7, printer in the print time is always out of paper or carbon belt ( TEC - 572). Cause: you run out of paper or carbon belt is wrong; Sent wrong with ordered provoked. The solution: to review the paper or whether carbon belt can accurately; Set on the mechanical parameters, and then stop after printing with accurate typesetting printing software Settings. 8, print, print is not clear, the ribbon is broken. ( 105Se/SL) Cause: printer carbon with shaft. The solution: carbon with mechanical shaft tension is too tight, regulate the printer carbon belt shaft pulling force. 9, print the new file to deformity, but can't open the old file and print. Cause: print collection, permissions. The solution: printing time, whether the collection once opened the file, if opened, must first turn off the ability to turn on another computer. And then test the collection authority. 10, print content when the print is not complete. Cause: printing software and driver version is too low. The solution: new version of the software and driver. 11, means less than stop typesetting software. Cause: the software not installed or computer performance. The solution: the new device software, if still not, presumably computer got a virus and anti-virus, please. Not again, please reinstall system. 12, machine shortly after boot, three lights are burning, print. Cause: the printer capacitance. The solution: to be a change in capacitance. 13, in the process of printing, print out the content is different from real content range. Cause: print driver. The solution: pick order accurate a printer driver. 14, beside emerge in the process of dark look line. ( argox1000 +) Cause: the print head no good. The solution: regulate print entered the screw. 15, machine RaoQi did not turn back, TEC - 572). Cause: set problem. The solution: adjusted the printer setup RaoQi back a variety of Settings, if not, is probably the main board performance, need to repair. 16, print, often emerge when jumping paper picture cause: print setup. The solution: in the paper intrusive and spacing are accurate, stop changing the BMP print pattern to PCX pattern printing. 17, stiff paper, in the process of recovery of different rings for: tooth * bad image body did not eliminate mechanical or mechanical. The solution: to eliminate the mechanical image or a change in tooth *. 18, in the printing process, often performance carbon bring exhausted cause: the mechanical PCB - F - or PCB G the solution: bad change PCB - F - or a change in PCB G。 19, in front of the stop thermal printer, rotation of the move, and performance of carbon belt run out. Cause: - rigid PCB G is broken
Xprinter Group thinks that that firms can avoid the artificial choice between quantitative and qualitative risk management, allowing both to play important roles in surfacing and assessing risks.
If you are thinking of having a , then you must be first clear about the purpose, which is driving you to buy this device. Xprinter Group offer quality for your needs with complete assurance of ability to serve your purpose.
A technology team created for insuring that pos 58 thermal printer is produced with the finest materials and technologies.
Choose the right platform for selling bluetooth wireless receipt printer and we'll reach the right customers. But if we have the right idea in the wrong platform, that still adds up to the wrong idea.
Xprinter Group are trained to think about problems and coming up with solutions, as well as presenting the whole idea in a logical and coherent manner.