loading

TSC barcode printers, common failures and solutions to a problem a _ printing devices

by:Xprinter     2020-06-26
Cause red light in the printing process: the printer no induction to the paper or induction sensors to the ribbon, to make the machine test paper again. Cause red light in the printing process: the printer no induction to the paper or induction sensors to the ribbon, to make the machine test paper again. Solution: turn off the printer power supply first, hold the PAUSE button on the printer, and then boot, such as a printer in thine hand, after the paper to see if the printer has a retraction, if not, the repeated according to the above methods to try a few times more, until the printer a retraction motion. If it tried again and again also not line, to initialize the machine to shut down, and then hold the PAUSE and FEED at the same time, two key until the three display lights on the printer after the flash again let go at the same time, and then at the beginning of the method under test paper, until a retraction actions occur. Printing paper jumping reasons: in the process of this kind of phenomenon still belongs to the machine failed to detect the cause of the paper or paper do not specification. Solution: check whether the bar code label paper is not standard, the size of each label are consistent, so for this reason, it can only change the barcode label paper. Such as detected label is no problem, it is belong to the machine failed to detect a piece of paper, test paper again. Turn off the machine first, and then hold the PAUSE and FEED at the same time two key switch on again, until the three display lights flashing at the same time let go to the machine once the initialization, and then turn it off, press and hold the PAUSE key to carry on the test paper, paper machine until after let go, until a retraction motion machine will begin to print later. Printers print process noise is very big, and the printer cover is hard to cover up. Reason: ribbon scroll binding backwards. Solution: check whether the ribbon scroll installed backwards, and properly installed. Walking in the process of printing paper is normal, but the print is printed out. Reason: the ribbon installed backwards. Solution: see ribbon is belong to the carbon or carbon, and then in according to the instructions on the installation methods are installed correctly. Print in the process of print is normal, but the color back to scroll back roll. Reason: this due to operator without installing ribbon in boot, lead to the printer failed to detect the ribbon, the default for the thermal printer. Solution: first, turn off the printer, correctly installed after the ribbon and barcode label paper boot, printer back to normal. Such as not to initialize the machine. Printing machine in the process of normal paper, but when the printing only printing half content or garbled words: software print application error. Solution: restart print program, to establish a new label, and the content on the label for layout, select the correct driver for printing to see if the normal printing. If still the same, it can only be uninstall and then reinstall the software. If still won't do, this is the computer print interface problems, must be replaced a new computer to print. Or a mouth for printing. Printer to print the paper feed is normal, but when the printing machine. Reason: the machine receive less than data. Solution: check whether the data interface of machine under wrong, look to whether the data line from mouth up, if it is, cable to parallel port. If not, to see if the printer port setup error. Click the start menu -> Settings -> printer to choose your machine's printer driver right click -> properties -> -> select LPT1 port, print back to normal. Open the software in a this printer is only support a limited number of the printer driver, please reinstall the correct printer driver warning window. Reason: software program error, leading to a printer driver is missing. Solution: if you print the software is installed in C disk directory, then open my computer to open the disk C, find and open the Program Files in this folder to find and open the Europlus this folder, find and open the Le - find and open the Bin - find and open the System to find Xprint. Inf the file and delete it. Print back to normal. Print is not clear why: good print Settings are not set or the print head is dirty. Solution: check whether the print head is dirty, clean the print head ( Note: when cleaning the print head, be sure to turn off the printer power supply first, otherwise, the print head is easy to damage) And then set the print temperature or try using a font ( Bold) 。 If not yet, may be the poor quality of printing ribbon or barcode label paper, replace good ribbon and barcode label paper. Print the black line is not clear and appear when reason: the print head is dirty or the print head is broken needle. The solution: cleaning the print head first, if not, can only replace the print head. ( Note: when cleaning the print head, be sure to turn off the printer power supply first, otherwise, the print head is easy to damage) 。
Custom message
Chat Online 编辑模式下无法使用
Leave Your Message inputting...
Hello, Thank you for contacting us ! We've received your message and will reply you soon. Have a nice day !