The failure of barcode printer system how to solve? _ printing equipment

by:Xprinter     2020-05-04

a lot of bar code printers, is in some principle and operation are interlinked, so small make up to you today about summarize saved to the production of bar code printer from labels printed common faults and accessories damage do a parsing, hope to help everyone. 1, always keep the tag changes when not, according to save there is a warning dialog box, according to the software after shut down. Reason: the user modify directly on the label changes caused by wrong operation. Solution: when a change is in the correct way of modifying modify or double-click to modify content, you write when the original layout dialog box on the modification, do not allow directly in the label on modification. This modified is back to normal. 2, all indicator lights flashing when the printer in the print does not test paper ( Zebra barcode printer) Reason: the sensor fault. The solution: cleaning the surface of the sensor dust or replace the sensor. 3, small printer in the print label will not reach the designated position, print the contents of partial or total up to partial reason: the label is too small, sensors are difficult to sensor to the paper. Solution: general label high at least more than 10 more than just good positioning, otherwise will be to offset Settings TAB. In the tag set, the label set to higher than the actual label tall a 5 mm or so, and then according to the specific migration situation to offset Settings TAB. 4, when the printing font clear, bar code not clear why: bar code content is too much, the density is too small. The solution: shorten the barcode content or increasing the density. For 200 dpi and 300 dpi machine, bar code density generally want to be in more than 7 mils to scaling factor to 2 or more than 2, print out the barcode is clear. 5, printed labels, always some words to print out the reason: the print head is dirty, the layout is wrong. The solution: cleaning the print head; In addition whether in typesetting to overlap the printed word, recomposition. 6, printer, the print is always shows no paper or carbon belt ( TEC - 572). Reason: you run out of paper or carbon belt is wrong; Sent wrong operation command. Solution: check paper or carbon belt is correct; Parameters set on the machine, then use printing software for printing after the correct layout Settings. 7 when printing, printing is not clear, the ribbon is broken. ( 105Se/SL) Reason: printer carbon belt shaft failure. Solution: carbon belt machine shaft tension is too tight, adjust printer carbon belt shaft under tension. 8, the new file can be normal print, but can't open the old file, unable to print. Reason: network printing, permissions error. Solution: print, whether on the Internet has opened this file, if you open, must first turn off can be opened on another computer. Then detect network access problems. 9, print content when the print is not completely. Reason: printing software and driver version is too low. Solution: install the new version of the software and drivers. 10, software cannot be typography. Reason: the software not installed or computer problems. The solution: to install the software, if not yet, may be computer got a virus and anti-virus, please. Not again, please reinstall the operating system. 11, machine shortly after boot, three lamp goes out, can't print. Reason: printer capacitance. Solution: need to replace the capacitor. 12, in the process of printing, print out the content and the actual content of different size. Reason: the print driver error. Solution: select the correct printer driver. In the process of the 13, beside black lines. ( argox1000 +) Reason: the print head no good. Solution: adjust the print entered the screw. 14, machine RaoQi did not turn back, TEC - 572). Reason: set wrong. Solution: set printer setup RaoQi back a variety of Settings, if not, may be a motherboard problem, need to repair. 15, often appear when printed paper jumping reason: print setup error. Solution: in the paper size and spacing is correct, change the BMP format printing to PCX format for printing.

Custom message
Chat Online 编辑模式下无法使用
Leave Your Message inputting...
Hello, Thank you for contacting us ! We've received your message and will reply you soon. Have a nice day !